<pre id="9t1tr"><del id="9t1tr"></del></pre>

        <p id="9t1tr"></p>
          <p id="9t1tr"></p><p id="9t1tr"><del id="9t1tr"></del></p>
          <p id="9t1tr"><del id="9t1tr"><dfn id="9t1tr"></dfn></del></p>

              <p id="9t1tr"></p>

                當前位置:首頁-新聞中心 > 新聞中心

                為了保證通風管道順利使用要進行正確安裝!

                發布人:http://www.honest-case.com   發布時間:2023-07-03 15:59:12

                大家都知道我們常用的通風管道要求采用不燃材料,是為了防止高溫引起火災或火災發生時火焰越過防火閥而造成更大的損失,那么為了保證通風管道順利使用要如何對其正確安裝加工呢?下面濟南通風管道廠家為您分析:

                Everyone knows that our commonly used ventilation ducts require the use of non combustible materials to prevent fires caused by high temperatures or greater losses caused by flames crossing the fire damper in the event of a fire. So, how to correctly install and process the ventilation ducts to ensure their smooth use? Below is an analysis by the ventilation pipeline manufacturer in Jinan:

                1、通風管道在運輸過程應有防止損傷風管的保護措施。

                1. Ventilation ducts should have protective measures to prevent damage to the ducts during transportation.

                2、榫接風管的連接在榫口處涂膠粘劑,是為增強接頭處的強度。

                2. The connection of the mortise and tenon air duct is coated with adhesive at the mortise to enhance the strength of the joint.

                3、當風管采用地面預組裝后架空安裝時,限制預組裝的長度是為了遮免風管因自重產生的彎曲而破壞構件接口。

                3. When the air duct is installed overhead after ground pre assembly, limiting the length of pre assembly is to prevent the bending of the air duct due to its own weight from damaging the component interface.

                4、玻璃纖維復合板風管端口為切割面時,在裝配法蘭連接件前應將管端切口面用膠帶或膠液進行封堵,才能防止玻璃纖維外露和飛散。

                4. When the end of the fiberglass composite board air duct is a cutting surface, the cutting surface of the pipe end should be sealed with tape or glue before assembling the flange connection to prevent the fiberglass from being exposed and flying.

                20220523388064.png

                5、非法蘭連接的玻璃纖維復合板風管垂直安裝的支撐件制作與安裝的方法。

                5. Method for manufacturing and installing support components for vertical installation of non flange connected glass fiber composite board air ducts.

                6、豎井內通風管道垂直安裝,由于空間少,又不便于以后檢修,故風管一般采用外套角鋼法蘭連接以增加連接點的牢固程度和強度,并把法蘭作成“井”形,吊筋直接吊在角鋼法蘭的吊耳上而不另設支撐件。

                6. The ventilation ducts inside the vertical shaft are installed vertically. Due to the limited space and inconvenient maintenance in the future, the air ducts are generally connected with outer angle steel flanges to increase the firmness and strength of the connection points. The flanges are also made into a "well" shape, and the hanging bars are directly hung on the lifting lugs of the angle steel flanges without additional support components.

                風管安裝加工是將法蘭的槽口套插在風管管板的端頭,用膠粘劑粘接。如果其間沒有過盈量,槽口和風管端面插入時會有間隙,使其無法粘為一體。更多相關事項就來我們網站http://www.honest-case.com咨詢!

                The installation and processing of air ducts involves inserting the groove of the flange into the end of the air duct board and bonding it with adhesive. If there is no interference between them, there will be a gap between the slot and the end face of the air duct when inserted, making it impossible to stick together. For more related matters, come to our website http://www.honest-case.com consulting service


                上一篇:一條完整的全自動風管生產線應實現什么功能
                下一篇:怎么做能降低鐵皮風管內的阻力呢?

                網站首頁 關于我們 產品展示 新聞中心 工程案例 在線留言 聯系我們

                成人免费区一区二区三区,亚洲AV成人一区二区三区观看在线,精品亚洲a∨无码一区二区三区,中文字幕一区二区三区日韩精品

                    <pre id="9t1tr"><del id="9t1tr"></del></pre>

                      <p id="9t1tr"></p>
                        <p id="9t1tr"></p><p id="9t1tr"><del id="9t1tr"></del></p>
                        <p id="9t1tr"><del id="9t1tr"><dfn id="9t1tr"></dfn></del></p>

                            <p id="9t1tr"></p>